Search found 391 matches

by brendon_m
Sun, 21 Jul 2019, 16:21
Forum: Technical and conversion discussion
Topic: Prelude conversion project - some questions
Replies: 535
Views: 41120

Re: Prelude conversion project - some questions

I wish it was only once. I'm still using it... :?
by brendon_m
Sun, 21 Jul 2019, 16:15
Forum: Technical and conversion discussion
Topic: Prelude conversion project - some questions
Replies: 535
Views: 41120

Re: Prelude conversion project - some questions

IMG_20190721_161417.jpg
IMG_20190721_161417.jpg (741.59 KiB) Viewed 1111 times
Sorry but I'm busy finding out the hard way why welding blankets aren't made of oil soaked cardboard...
by brendon_m
Sun, 21 Jul 2019, 16:00
Forum: Technical and conversion discussion
Topic: Prelude conversion project - some questions
Replies: 535
Views: 41120

Re: Prelude conversion project - some questions

That's probably the fan relay, try using a multi meter on the coil terminals of the relay and see if there is a bit of voltage floating around. It wouldnt be much. Also try swapping the relay if you have one the same. I've seen water inside relays causing them to track and latch on
by brendon_m
Sun, 21 Jul 2019, 15:48
Forum: Technical and conversion discussion
Topic: Prelude conversion project - some questions
Replies: 535
Views: 41120

Re: Prelude conversion project - some questions

Try pulling fuse 17 with the key on and see if the fan starts up again
by brendon_m
Sun, 21 Jul 2019, 15:46
Forum: Technical and conversion discussion
Topic: Prelude conversion project - some questions
Replies: 535
Views: 41120

Re: Prelude conversion project - some questions

What I was trying to say is I reckon the relay is getting a positive on the blue wire (just enough to turn on a relay but not much more and it sounds like not even enough power to run 2 relays, hence the condenser fan dropping out) and then the circuit gets a ground from the black/yellow wire throug...
by brendon_m
Sun, 21 Jul 2019, 15:00
Forum: Technical and conversion discussion
Topic: Prelude conversion project - some questions
Replies: 535
Views: 41120

Re: Prelude conversion project - some questions

Looking at your diagram I'd guess that the blue wire that goes to the fan switch I've circled is probably floating high. Did you mess with any blue wires in the engine bay? If you find that wire and probe it and see what's there. If I'm right then it couldn't be much power because it would be a shor...
by brendon_m
Fri, 12 Jul 2019, 19:16
Forum: Batteries, charging, management and monitoring
Topic: Disposing of old lithium batteries
Replies: 12
Views: 934

Re: Disposing of old lithium batteries

There was some company who recycles old EV cells and found that new cells made from recycled lithium (and the other stuff) outperformed "virgin" material made cells
by brendon_m
Thu, 11 Jul 2019, 11:21
Forum: Members Machines
Topic: Brendon_m Moke
Replies: 167
Views: 14912

Re: Brendon_m Moke

I could paint it rattle can flat black for that stolen look
by brendon_m
Thu, 11 Jul 2019, 07:18
Forum: For Sale/Wanted
Topic: Tesla model x motors
Replies: 2
Views: 481

Re: Tesla model x motors

In the description of the video they mention that software needs to be changed before their control would work and it can't be done remotely. So unless someone in Australia does the hard work as well, these front motors are basically useless (for now anyway). I guess the rear motor could be used wit...
by brendon_m
Wed, 10 Jul 2019, 17:55
Forum: For Sale/Wanted
Topic: Tesla model x motors
Replies: 2
Views: 481

Tesla model x motors

Found this model x being wrecked in Leppington NSW. TESLA MODEL X MOTORS, https://www.gumtree.com.au/s-ad/leppington/cars-vans-utes/tesla-model-x-motors/1217268395?utm_source=com.google.android.apps.docs&utm_medium=social&utm_campaign=socialbuttons&utm_content=app_android Batteries are all gone and ...
by brendon_m
Tue, 09 Jul 2019, 13:54
Forum: Members Machines
Topic: Brendon_m Moke
Replies: 167
Views: 14912

Re: Brendon_m Moke

I've managed to finish up one of my packs and squeezed it into place. I'm thinking I should call this build "project snug" because there isn't a lot of clearance... anywhere. I had to lift the back end in half way, then the front and slide it forward and then the back the rest of the way. All while ...
by brendon_m
Tue, 02 Jul 2019, 19:27
Forum: For Sale/Wanted
Topic: 2016 BMW i3 Wreck (BEV) (sold)
Replies: 9
Views: 657

Re: 2016 BMW i3 Wreck (BEV)

Images don't work for me either. Just says image with an icon a bunch of times
by brendon_m
Mon, 01 Jul 2019, 08:03
Forum: Hyundai
Topic: Hyundai Sales Tactics
Replies: 38
Views: 2316

Re: Hyundai Sales Tactics

Like putting an electric car in the oven to dry the paint. Im sure the batteries would love that. There are basic training courses for panel beaters to take so they can know how to safely work on EVs (how to isolate etc). Really anyone in an automotive trade should go on one before touching an EV an...
by brendon_m
Sun, 30 Jun 2019, 10:37
Forum: Members Machines
Topic: Qld Moke
Replies: 7
Views: 880

Re: Qld Moke

I'd say find an aftermarket replacement to the gearbox because using it is a pain, on the other hand I never found a reasonable cost alternative.
by brendon_m
Thu, 27 Jun 2019, 05:53
Forum: Nissan
Topic: Nissan Australia Leaf 1.0 battery replacement
Replies: 12
Views: 3425

Re: Nissan Australia Leaf 1.0 battery replacement

BTW: I'm not sure if the US price is change-over though. I'd guess so. Nissan seems to have a strong desire to keep their packs out of the hands of us lowly commoners. I have heard of deals with 2nd life companies that buy the packs for home storage so there are probably contacts that force Nissan ...
by brendon_m
Wed, 26 Jun 2019, 13:18
Forum: Batteries, charging, management and monitoring
Topic: Battery interconnect sizing
Replies: 48
Views: 2467

Re: Battery interconnect sizing

Richo wrote:
Wed, 26 Jun 2019, 13:07
The aluminum doesn't care if its at 25Deg or 300Deg.
True, but to heat aluminium to 300 degrees takes energy, and that energy is coming from the pack.
Although my experience of aluminium is you look at it with an angle grinder in your hand and it instantly jumps to 1000000°c
by brendon_m
Wed, 26 Jun 2019, 07:42
Forum: Tesla EVs
Topic: Tesla advert for a car that doesn't exist
Replies: 10
Views: 988

Re: Tesla advert for a car that doesn't exist

Bit more of the build for those interested.

https://youtu.be/zZbAjhMiMG8
by brendon_m
Fri, 21 Jun 2019, 17:49
Forum: Tesla EVs
Topic: Tesla advert for a car that doesn't exist
Replies: 10
Views: 988

Re: Tesla advert for a car that doesn't exist

Don't get me wrong, I enjoy the channel. I just like nitty gritty "boring" stuff.
by brendon_m
Fri, 21 Jun 2019, 08:09
Forum: Tesla EVs
Topic: Tesla advert for a car that doesn't exist
Replies: 10
Views: 988

Re: Tesla advert for a car that doesn't exist

Yeah, I was a bit disappointed in the lack of intricate details but its not an in depth channel, more just a catalogue of cool/funny things. I was expecting more from the other contributors maybe they'll release their own videos with more nitty gritty on the build down the line. But that being said,...
by brendon_m
Thu, 20 Jun 2019, 15:59
Forum: Tesla EVs
Topic: Tesla advert for a car that doesn't exist
Replies: 10
Views: 988

Re: Tesla advert for a car that doesn't exist

Here's the link to the build /conversion vid


https://youtu.be/jKv_N0IDS2A
by brendon_m
Thu, 20 Jun 2019, 15:24
Forum: Members Machines
Topic: Brendon_m Moke
Replies: 167
Views: 14912

Re: Brendon_m Moke

I've been progressing along with the battery packs. The frames are mostly done I just need to finish the mounting bits and reinforcing where the packs bolt to the body work. IMG_20190620_102948.jpg Also I've made the majority of the interconnects. The pack will be split in 2 packs of 13s 3p making 2...
by brendon_m
Tue, 18 Jun 2019, 10:53
Forum: Tesla EVs
Topic: Model 3 lowest cost in Aus?
Replies: 11
Views: 950

Re: Model 3 lowest cost in Aus?

Well the configurator in WA comes in at $72109. Delivered and ready to drive
Screenshot_2019-06-18-10-54-33-325_com.android.chrome.png
Screenshot_2019-06-18-10-54-33-325_com.android.chrome.png (192.68 KiB) Viewed 943 times
by brendon_m
Mon, 17 Jun 2019, 19:40
Forum: Batteries, charging, management and monitoring
Topic: Battery interconnect sizing
Replies: 48
Views: 2467

Re: Battery interconnect sizing

A lot of the cells are in parallel so each cell only sees a small portion of the current. Each of your cells will see 1/2 the total current but from 1 pair of cells to next will be the whole kabootle Got it, thanks for clarifying! Just to clarify further it's not exactly half because you have diffe...
by brendon_m
Mon, 17 Jun 2019, 18:17
Forum: Batteries, charging, management and monitoring
Topic: Battery interconnect sizing
Replies: 48
Views: 2467

Re: Battery interconnect sizing

A lot of the cells are in parallel so each cell only sees a small portion of the current.
Each of your cells will see 1/2 the total current but from 1 pair of cells to next will be the whole kabootle
by brendon_m
Sun, 16 Jun 2019, 06:44
Forum: Mitsubishi
Topic: Servicing Imiev (90K service) K Mart??
Replies: 4
Views: 656

Re: Servicing Imiev (90K service) K Mart??

My work used to do bonuses, it was something like 3% of the profit you created and we would get it every 2nd payday. It was nice but wasn't going to buy a Ferrari. Maybe it was just me but I never even thought about the bonus when talking to customers. As far as I know no-one else ever thought about...